| Option | Order No. | |
|---|---|---|
| Flexible Pt100 temperature sensor, positioned flexibly in chamber or load, for local temperature measurement (up to 2 additional sensors are possible). The measured temperature can, if required, be indicated on the display, recorded in the integral data store, and can be documented via the AtmoCONTROL software | H8 | |
| 4 – 20 mA current loop interface (0 to +260 °C ≙ 4 - 20 mA) Temperature controller actual value | V3 | |
| 4 – 20 mA current loop interface (0 to +260 °C ≙ 4 - 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber fo external temperature monitoring (max. 1 SingledDISPLAY, max. 3 TwinDISPLAY) - price per sensor | V6 | |
| Locking mechanism to prevent simultaneous opening of doors for contamination protection in case of wall installation | D5 | |
| Light module warm white 2,700 K: light strips arranged on the side walls of the interior, 10 for model 110, 14 for model 260/400/750, programme-controlled dimming from 0 to 100 % (in 1 % steps), ramp programming in combination with temperature (only with TwinDisplay) | T9 | |
| Premium module: comprises the inert gas inlet (only size 49 and 101), extra connectors for thermoshelves, 1 (size 29), 2 (sizes 49/101), an additional thermoshelf (sizes 49/101) | T5 | |
| Temperature restriction; Temperatures: +60, +70, +80, +95, +100, +120, +160 or +180 °C (Please, indicate upon ordering) | A8 | |
| MobileALERT for 2 alarm notifications; temperature and vacuum alarm (only with option T5) | C4 | |
| Flexible Pt100 for positioning in chamber or in load with socket, 4-pin, according to NAMUR NE 28, for external temperature recording (load temperature) | H4 | |
| Potential-free contact (24 V/2 A) with socket, according to NAMUR NE 28 for combination error message (e.g. supply failure, sensor fault, fuse) | H6 | |
| Freely positioned control sensor, MIN and MAX alarm adjustable at ControlCOCKPIT, alarm values captured in internal data logger | H9 | |
| 4 – 20 mA current loop interface (only with option T5) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring - price per sensor | V6 | |
| 4 – 20 mA current loop interface (only with option T5) Vacuum actual value (0 bis 1200 mbar = 4 - 20) | W2 | |
| 4 – 20 mA current loop interface (only with option T5) Temperature actual value (0 to 210 °C = 4 - 20 m) | V3 | |
| 4 – 20 mA current loop interface O2 controller, actual value (0 – 25 % O2 4 – 20 mA) | V1 | |
| 4 – 20 mA current loop interface CO2 controller, actual value (0 – 25 % CO2 4 – 20 mA) | V9 | |
| Castor frame (2-part), height 140 mm | R9 | |
| 4 – 20 mA current loop interface Humidity controller, actual value (0 – 100 % rh 4 – 20 mA) | V7 | |
| Works calibration certificate for one temperature according to customer specification (only TTC) | D00109 | |
| Start-up of ICOmed incubators and brief training (D, A, CH only), through Memmert service, not subject to discount | K9 | |
| Works calibration certificate for 5 %, 7 % and 10 % CO2 (measured at +37 °C) special works calibration certificates upon request | D00106 | |
| 4 – 20 mA current loop interface Temperature controller, actual value (0 to +70 °C 4 – 20 mA) | V3 | |
| Inner door with partitioned glass doors | K4 | |
| Entry port (silicone), 40 mm clear diameter, for introducing connections, moisture tight, can be closed by silicone stopper, at the back, centre right; not available for ICO50med with active humidity control (option K7) or humidity display (option K6) | F7 | |
| Capacitive humidity sensor for measuring and displaying the relative humidity | K6 | |
| Peltier cooling unit enables a working temperature of 37 °C even at higher ambient temperatures of up to 35 °C | K5 | |
| Control of oxygen concentration by N2 inlet; adjustment range 1 % up to 20 % O2; setting accuracy 0.1 % (requires option K7) | T6 | |
| Active microprocessor control for humidifying and dehumidifying (40 – 97 % rh), incl. digital indication and auto-diagnostic system ensures even more rapid reaching of set humidity and very short recovery times while avoiding condensate formation. Humidity supply with distilled water (from an external tank) by a self-priming pump; integral bacteria block by generating hotsteam, dehumidifying via sterile filter | K7 | |
| Electropolished interior | T2 | |
| MobileALERT for up to 4 alarm notifications; standard: temperature and CO2 alarm, additionally humidity alarm (when equipped with option K7) and O2 alarm (when equipped with option T6) | C4 | |
| Battery-buffered ControlCOCKPIT. Uninterrupted supply for the entire display unit (ControlCOCKPIT) and therefore complete documentation of all parameteres even when there is a power failure. The CO2 parameter is continously regulated. | C2 | |
| Voltage 115 V, 50/60 Hz (no extra cost) | X2 | |
| Extended overtemperature protection for SingleDISPLAY devices by additionally integrated Pt100 sensor for independent temperature monitoring for models UN/UF | A6 | |
|
Full-sight glass door (4 insulating glass). Temperature-range up to max. 250 °C. | B0 |
|
|
Full-sight glass door (4 insulating glass). Temperature-range up to max. 300 °C - extra cost | B1 |
|
Fresh-air filter (filtration efficiency 80 %) mounted at the bottom (for UF/UFplus). For model sizes 30 – 260, subframe or subframe on castors obligatory | R8 |
|
Interior lighting for observing the load | R0 |
| Interior socket (can only be ordered with limited temperature-range – max. +70°C - option A8 necessary) current carrying ampacity 230 V, 2.2 A can be switched off with the On/Off switch, cannot be switched individually, moisture tight IP68 | R3 | |
| Interior nearly gastight | K2 | |
| Interior nearly gastight with possibility for inlet/outlet through 2 tubes with ball valves | K3 | |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, can be closed by flap, position left centre/centre | F0 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, can be closed by flap, position left centre top | F1 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, can be closed by flap, position right centre/centre | F2 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, can be closed by flap, position right centre top | F3 |
|
Entry port, 23 mm clear diameter for introducing connections at the side, can be closed by flap in special positions (please, state location) - left | F4 F1 |
|
Entry port, 23 mm clear diameter for introducing connections at the side, can be closed by flap in special positions (please, state location) - right | F5 |
|
Entry port, 23 mm clear diameter for introducing connections, can be closed by flap in special positions (please, state location) - rear | F6 |
|
Entry port, 14 mm clear diameter, can be closed by flap, in special positions at the back (please, state location) | D6 |
|
Entry port, 38 mm clear diameter, can be closed by flap, in special positions at the back (please, state location) | F7 |
|
Entry port, 57 mm clear diameter, can be closed by flap, in special positions at the back (please, state location) | F8 |
|
Entry port, 100 mm clear diameter, can be closed by flap, in special positions at the back (please, state location) | F9 |
| 4 – 20 mA current loop interface (0 to +310°C corresponds to 4 – 20 mA) Temperature controller actual value | V3 | |
| 4 – 20 mA current loop interface (0 to +310°C corresponds to 4 – 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 1 SingleDISPLAY, max. 3 TwinDISPLAY) | V6 | |
| Fan speed monitoring with switching off the heating and with alarm in case of failure – optional for UFplus only | V4 | |
|
Works calibration certificate for 3 temperatures: +100°C, +160°C, +220°C. Standard works calibration certificate (measuring point chamber centre) at +160°C | D00128 |
| Chamber modification for the application of reinforced perforated stainless steel shelves or stainless steel grids (bearing rails mounted in the working chamber) – includes replacement of 2 standard grids by 2 reinforced grids | K1 | |
| Extended overtemperature protection for SingleDISPLAY devices by additionally integrated Pt100 sensor for independent temperature monitoring for models IN/IF | A6 | |
| Interior socket (can only be ordered with limited temperature-range – max. +70°C - option A8 necessary) current carrying ampacity 230 V, 2.2 A can be switched off with the On/Off switch, cannot be switched individually, moisture tight IP68 (only with SingleDISPLAY) | R3 | |
| 4 – 20 mA current loop interface (0 to +90°C corresponds to 4 – 20 mA) Temperature controller actual value | V3 | |
| 4 – 20 mA current loop interface (0 to +90°C corresponds to 4 – 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 1 SingleDISPLAY, max. 3 TwinDISPLAY) | V6 | |
| Fan speed monitoring with switching off the heating and with alarm in case of failure – optional for IFplus only | V4 | |
|
Works calibration certificate for 3 temperatures: +37°C, +52°C, +70°C. Standard works calibration certificate (measuring point chamber centre) at +37°C | D00126 |
| Extended overtemperature protection for SingleDISPLAY devices by additionally integrated Pt100 sensor for independent temperature monitoring for models SN/SF | A6 | |
| Fresh-air filter (filtration efficiency 80 %) mounted at the bottom (for SF/SFplus). For model sizes 30 – 260, subframe or subframe on castors obligatory | R8 | |
| 4 – 20 mA current loop interface (0 to +260°C corresponds to 4 – 20 mA) Temperature controller actual value | V3 | |
| 4 – 20 mA current loop interface (0 to +260°C corresponds to 4 – 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 1 SingleDISPLAY, max. 3 TwinDISPLAY) | V6 | |
| Fan speed monitoring with switching off the heating and with alarm in case of failure – optional for SFplus only | V4 | |
| Works calibration certificate for 3 temperatures: +160°C, +180°C, +250°C. Standard works calibration certificate (measuring point chamber centre) at +160°C | D00132 | |
| Inert gas inlet: programmable and digitally controlled inlet for inert gas with flow rate reduction | W5 | |
| Premium module: comprises the inert gas inlet (only size 49 and 101), extra connectors for thermoshelves, 1 (size 29), 2 (sizes 49/101), an additional thermoshelf (sizes 49/101) | ||
| Extended temperature-range (0°C to +90°C) | A8 | |
| Interior socket, ampacity 230 V/2.2 A, can be switched off with the On/Off switch, cannot be switched individually, moisture tight IP68 | R3 | |
| 4 – 20 mA current loop interface (-10 to +80°C corresponds to 4 – 20 mA) Temperature controller actual value | V3 | |
| 4 – 20 mA current loop interface (-10 to +80°C corresponds to 4 – 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 1 SingleDISPLAY, max. 3 TwinDISPLAY) | V6 | |
|
Works calibration certificate for 3 temperatures: +5°C, +37°C, +60°C. Standard works calibration certificate (measuring point chamber centre) at +10°C and +37°C | D00129 |
| Light module cold white 6,500 Kelvin: light strips arranged on the side walls of the interior, 10 strips for model 110, 14 for model 260/750, programme-controlled dimming from 0 to 100 % (in 1 % steps), ramp programming in combination with temperature (only with TwinDISPLAY) | T7 | |
| Light module warm white 2,700 K: light strips arranged on the side walls of the interior, 10 for model 110, 14 for model 260/400/750, programme-controlled dimming from 0 to 100 % (in 1 % steps), ramp programming in combination with temperature and humidity | T9 | |
| Light module cold white 6,500 Kelvin + warm white 2,700 Kelvin: LED light strips -10 strips for model 110, 14 for model 260/750 - (5 resp. 7 alternating cold white light strips and 5 resp. 7 warm white light strips) on the side walls of the interior, programmecontrolled dimming from 0 to 100 % (in 1 % steps), ramp programming in combination with temperature (only with TwinDISPLAY) | T8 | |
| Voltage 115 V, 50/60 Hz | X2 | |
| 4 – 20 mA current loop interface (-20 to +70°C corresponds to 4 – 20 mA) Temperature controller actual value | V3 | |
| 4 – 20 mA current loop interface (-20 to +70°C corresponds to 4 – 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 3 TwinDISPLAY) | V6 | |
| Fan speed monitoring with switching off the heating and with alarm in case of failure | V4 | |
| Entry port (silicone), 40 mm clear diameter, for introducing connections, moisture tight, can be closed by silicone stopper, at the back (please, state location) | F7 | |
|
Works calibration certificate for 3 temperatures: 0°C, +37°C, +60°C. Standard works calibration certificate (measuring point chamber centre) at +10°C and +37°C | D00130 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, moisture tight, can be closed by flap and silicone stopper, standard position left centre/centre | F0 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, moisture tight, can be closed by flap and silicone stopper, standard position left centre top | F1 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, moisture tight, can be closed by flap and silicone stopper, standard position right centre/centre | F2 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, moisture tight, can be closed by flap and silicone stopper, standard position right centre top | F3 |
|
Entry port, 23 mm clear diameter for introducing connections at the side, moisture tight, can be closed by flap and silicone stopper (please, state location) - left | F4 |
|
Entry port, 23 mm clear diameter for introducing connections at the side, moisture tight, can be closed by flap and silicone stopper (please, state location) - right | F5 |
|
Entry port, 23 mm clear diameter for introducing connections at the side, moisture tight, can be closed by flap and silicone stopper (please, state location) - rear | F6 |
| 4 – 20 mA current loop interface (-10 to +80°C corresponds to 4 to 20 mA) Temperature controller, actual value | V3 | |
| 4 – 20 mA current loop interface (-10 to +80°C corresponds to 4 to 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 3 TwinDISPLAY) | V6 | |
| 4 – 20 mA current loop interface (-10 to +80°C corresponds to 4 to 20 mA) Humidity controller, actual value (0 – 100 % rh corresponds to 4 – 20 mA) | V7 | |
| Works calibration certificate for one (freely selectable) temperature and humidity value. Standard works calibration certificate (measuring point chamber centre) at +10°C, +37°C and 60 % rh at +30°C (sizes 1060/1400 for +25 °C/40 % rh and +40 °C/75 % rh) | D00105 D00143 | |
| Compressed air dehumidification (efficient dehumidification of the interior by means of compressed air). Standard works calibration certificate (measuring point chamber centre) at +10 °C with 10 % rh. | C9 | |
| Door-hinges on left side | B8 | |
| Works calibration certificate for 80 % rh (measured at +50°C) | D00107 | |
| Start-up of HCP and brief training (D, A, CH only) through MEMMERT service, (not subject to discount) | K9 | |
| Stacking version for 2 units of equal size (bottom unit modification) | G3 | |
| Process-dependent electromagnetic door lock | D4 | |
|
Water level control (for WNB, WNE, WPE) | L3 |
|
Works calibration certificate (37°C for WNB, WNE, WPE, 160°C for ONE) | D00123 |
| Adjustable temperature limiter, safety device class 2 instead of adjustable overheat controller safety device class 3.1, no extra cost | ||
|
Full-sight glass door triple-insulating glass) | B0 |
| Reinforced chamber (max. loading up to 300 kg (involves narrower reinforced grids) includes replacement of 2 standard grids by 2 reinforced grids | ||
| Process-dependent electromagnetic door lock (both sides) | D4 | |
| Locking mechanism with SPS control to prevent simultaneous opening of doors for contamination protection in case of wall installation | ||
| Works calibration certificate for one temperature and humidity according to customer specification (only CTC) | D00110 | |
| Full-sight glass door (5-layer insulating glazing), heated | B0 | |
| Entry port, left, 80 mm, with stopper | F0 | |
| Start-up of CTC and TTC chambers and brief training (D, A, CH only) through Memmert service, (not subject to discount) | K9 | |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, gas tight, can be closed by flap and silicone stopper, standard position left centre/centre | F0 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, gas tight, can be closed by flap and silicone stopper, standard position left centre top | F1 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, gas tight, can be closed by flap and silicone stopper, standard position right centre/centre | F2 |
|
Entry port, 23 mm clear diameter, for introducing connections at the side, gas tight, can be closed by flap and silicone stopper, standard position right centre top | F3 |
|
Entry port, 23 mm clear diameter for introducing connections at the side, gas tight, can be closed by flap and silicone stopper, in special positions (please, state location) - left | F4 |
|
Entry port, 23 mm clear diameter for introducing connections at the side, gas tight, can be closed by flap and silicone stopper, in special positions (please, state location) - right | F5 |
|
Entry port, 23 mm clear diameter for introducing connections at the side, gas tight, can be closed by flap and silicone stopper, in special positions (please, state location) - rear | F6 |
| Entry port, 40 mm clear diameter, for introducing connections, gas tight, can be closed by flap and silicone stopper, in special positions at the back (please, state location) | F7 | |
| 4 – 20 mA current loop interface (0 to +90°C corresponds to 4 – 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 3 TwinDISPLAY) | V6 | |
| Gas inlet/outlet through 2 tubes with ball valves | K3 | |
| Works calibration certificate for 3 temperatures: +37°C, +52°C, +70°C. Standard works calibration certificate (measuring point chamber centre) at +80°C | D00126 | |
| 4 – 20 mA current loop interface (0 to +70°C corresponds to 4 – 20 mA) Temperature controller actual value | V3 | |
| 4 – 20 mA current loop interface (0 to +70°C corresponds to 4 – 20 mA) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 1 SingleDISPLAY) | V6 | |
| Works calibration certificate for a freely selectable temperature value. Standard works calibration certificate (measuring point chamber centre) at +18°C and +25°C | D00131 | |
|
Entry port, 120 mm clear diameter, can be closed by flap, in special positions at the back (please, state location) | |
| Alternative light boxes (replace the standard lighting; have to be ordered together with the chamber); number of fluorescent lamps: size 110: 5, sizes 260/750: 6, with cold white light (daylight: light colour 865, 6.500K; daylight complies with standard illuminant D65) (only ICHeco L/ICH L) one box | T81 | |
| Alternative light boxes (replace the standard lighting; have to be ordered together with the chamber); number of fluorescent lamps: size 110: 5, sizes 260/750: 6, with cold white light (daylight: light colour 865, 6.500K; daylight complies with standard illuminant D65) (only ICHeco L/ICH L) second box (cannot be switched on separately) | T82 | |
| Alternative light boxes (replace the standard lighting, have to be ordered together with the chamber), number of fluorescent UV lamps: size 110: 5, sizes 260/750: 6, in the spectral range of 315 to 400 nm, 22 W/m2, (only ICH L) one box, no extra cost | T01 | |
| 4 to 20 mA current loop interface (-20 to +70°C corresponds to 4 to 20 mA) (Models ICH C max. 2 interfaces – only combination V3 + V7 or V3 + V9 possible) Temperature controller, actual value | V3 | |
| 4 to 20 mA current loop interface (-20 to +70°C corresponds to 4 to 20 mA) (Models ICH C max. 2 interfaces – only combination V3 + V7 or V3 + V9 possible) Temperature of a Pt100 sensor positioned flexibly in chamber for external temperature monitoring (max. 3 TwinDISPLAY) | V6 | |
| 4 to 20 mA current loop interface (-20 to +70°C corresponds to 4 to 20 mA) (Models ICH C max. 2 interfaces – only combination V3 + V7 or V3 + V9 possible) Humidity controller, actual value (0 – 100 % corresponds to rh 4 – 20 mA) | V7 | |
| 4 to 20 mA current loop interface (-20 to +70°C corresponds to 4 to 20 mA) (Models ICH C max. 2 interfaces – only combination V3 + V7 or V3 + V9 possible) CO2 controller, actual value (0 – 25 % CO2 corresponds to 4 – 20 mA) | V9 | |
| Works calibration certificate for one (freely selectable) temperature and humidity value. Standard works calibration certificate (measuring point chamber centre) at +10°C, +37°C and +30°C with 60 % rh | D00121 | |
| Compressed air dehumidification (efficient dehumidification of the interior by means of compressed air – for models ICH and ICH L). Standard works calibration certificate (measuring point chamber centre) at +10 °C with 10 % rh. | C9 | |
| Illumination unit consisting of 4 fluorescent lights with cold white light (standard illuminant D65, 6,500 K) and 2 UV lamps in the spectral range of 320 to 400 nm, 8 W/m2, acc. ICH Q1B option 2, light intensity approx. 8,000 Lux, separately switchable via controller (only ICH L) second box | T72 | |
| Alternative light boxes (replace the standard lighting, have to be ordered together with the chamber), number of fluorescent UV lamps: size 110: 5, sizes 260/750: 6, in the spectral range of 315 to 400 nm, 22 W/m2, (only ICH L) second box, cannot be switched on seperately | T02 | |
| Chamber modification for the application of reinforced perforated stainless steel shelves or stainless steel grids (bearing rails mounted in the working chamber) – includes replacement of 2 standard grids by 2 reinforced grids (ICH and ICH C only) | K1 | |
| Two gas connections with quick release connectors, automatic switch-over of gas cylinders; incl. two CO2 connection sets: hose with coupling and clamp | T1 | |
| Hygiene module: electropolished interior seamlessly welded by laser | T2 | |
| Communication module: USB interface, "Celsius" standard software for programming and logging, ring log memory, printer interface | T3 | |
| CO2 module: extended CO2 range from 0 to 20 % | T4 | |
| Premium module: includes Comfort, Hygiene, Communication and CO2 module | T5 | |
| Humidity-Modul: active microprocessor control for humidifying and dehumidifying (40-97 % rh), incl. digital indication and auto-diagnostic system ensures even more rapid reaching of set humidity and very short recovery times while avoiding condensate formation, recommended for applications with set O2 values of less than 10 %, humidity supply with distilled water (from an external tank) by a self-priming pump, integral bacteria block by generating hotsteam, dehumidifying via sterile filter, (standard humidity limit control and water dishes are omitted). Can only be ordered together with new incubator | K7 | |
| O2 module: control of oxygen concentration by N2 inlet, adjustment range 1 % up to 20 % O2, setting accuracy 0,1 %, (Combination of comfort module or Premium module and O2 module not possible), for applications with a set O2-value of less than 10 %, the humidity module is highly recommended. | T6 | |
| Entry port (silicone), 40 mm clear diameter, for introducing connections, moisture tight, can be closed by silicone stopper, at the back either centre right or centre left (please, state location) | F7 | |
|
Potential-free contact (24V/2A) with socket 3 pin, according to NAMUR NE 28 for external monitoring (setpoint of temperature and CO2 is reached) | H5 |
| Works calibration certificate for 5 %, 7 % and 10 % CO2 (measured at +37°C) | D00106 | |
| Start-up of INCO incubators and brief training (D, A, CH only), through MEMMERT service, not subject to discount | K9 | |
| 4-part partitioning of interior with gas baffle (replacement of 3 full-width by 6 half-width shelves) | K4 | |
| Interface Ethernet instead of USB including software | W4 | |
| RS232 interface instead of USB | W6 | |
| Computer interface RS485 (for networking a max. of 16 ovens) instead of RS232 | V2 | |
| Door with lock (safety lock, not available for VO, VOcool, TTC/CTC) | B6 | |
|
Flexible Pt100 for positioning in chamber or in load with socket, 4-pin, according to NAMUR NE 28, for external temperature recording (load temperature) | H4 |
|
Flexible Pt100 temperature sensor, positioned flexibly in chamber or load, for local temperature measurement (up to 3 additional sensors are possible). The measured temperature can, if required, be indicated on the multifunction display, recorded in the integral ring store, and can be documented via the “Celsius” software or on an attached printer. (not available for VO, VOcool, TTC and CTC) | H8 |
|
Potential-free contact (24 V/2 A) with socket, according to NAMUR NE 28 for external monitoring (indicates when setpoint is reached); VO only in combination with option T5 | H5 |
|
Potential-free contact (24 V/2 A) with socket, according to NAMUR NE 28 for combination error message (e.g. supply failure, sensor fault, fuse); VO only in combination with option T5 | H6 |
|
Potential-free contact (24 V/2 A) with socket, according to NAMUR NE 28, triple, for signal generation, controlled by programme segment for a total of 3 freely selected functions to be activated (e.g. acoustic and visual signals, exhaust motors, fans, stirrers etc.) | H7 |
|
Door with lock (safety lock), Standard with SN/SF and SNplus/SFplus 450 and 750 | B6 |
| Door hinged on the left | B8 | |
|
Potential-free contact (24 V/2 A) with socket to NAMUR NE 28 for external monitoring (indicates when setpoint is reached) | H5 |
|
Potential-free contact for combination error message (e.g. supply failure, sensor fault, fuse) | H6 |
|
Potential-free contact (24 V/2 A) with socket to NAMUR NE 28, for signal generation, controlled by programme segment, for free-selectable functions to be activated (e.g. activation of audible and visual signals, exhaust motors, fans, stirrers, etc. Only for units with TwinDISPLAY; max 2 contacts on 1-phase appliances; max 4 contacts on 3-phase appliances, 2 contacts | H7 H72 |
| Process-dependent programmable door lock (only for units with TwinDISPLAY) | D4 | |
| Door-open-recognition (only for units with TwinDISPLAY) | V5 | |
|
Flexible Pt100 for positioning in chamber or in load with socket, 4-pin, according to NAMUR NE 28, for external temperature recording (load temperature) max. 3 sensors | H4 |
|
Additional Pt100 temperature sensor, positioned flexibly in chamber or load, for local temperature measurement (up to 3 additional sensors are possible). The measured temperature can, if required, be indicated on the display, recorded in the integral ring store, and can be documented via the AtmoCONTROL software or on an attached printer. | H8 |
| MobileALERT, notification by SMS in case of any error or alarm of the device. Requires option H6 “floating contact for alarm” | C3 | |
| Temperature restriction (for models UN/UF/UNplus/UFplus, IN/IF/INplus/IFplus) Temperatures: +60, +70, +80, +95, +100, +120, +160, +180, +200 or +220 °C (Please, indicate upon ordering) | A8 | |
|
Castor frame (2-part), height 140 mm | R9 B29762 B29763 B29764 |
| Potential-free contact (24 V/2 A) with socket to NAMUR NE 28, for signal generation, controlled by programme segment, for a total of 3 freely selectable functions to be activated (e.g. activation of audible and visual signals, exhaust motors, fans, stirrers, etc. (only for units with TwinDISPLAY), max 2 contacts for 1-ph. units, max 4 contacts for 3-ph. units,4 contacts | H74 |
| Accessory | Order No. | |
|---|---|---|
| Flush-fit unit set (stainless steel frame covering gap between oven and wall opening), without air slots - technical clarification required | B33204 B33205 B33206 B33207 | |
| Additional reinforced stainless steel grid, electropolished, max. loading 60 kg; with guide bars and fixing screws (only in connection with option K1). Please consider max. loading of chamber | B32190 | |
| IQ/OQ document with device-specific works test data for one free-selectable temperature and vacuum value, incl. temperature distribution survey at Memmert for 5 measuring points per thermoshelf to DIN 12880:2007-05. PQ check list as support for validation by customer valid for one thermoshelf; dito further thermoshelves, price on demand. Price for validation at customer site on demand | D00117 D00136 | |
| Noise-insulated vacuum pump module, as above, however with built-in pump, 230 V, 50/60 Hz | PMP29 PMP49 PMP101 | |
| Noise-insulated vacuum pump module without pump (exterior dimensions and -material No. s. vacuum oven) with antivibration metal plate at the bottom to accommodate the vacuum pump, incl. full-sight glass door. Socket, signal cable and connecting hose to the vacuum oven | PM29 PM49 PM101 | |
| Works calibration certificate for 3 temperatures: +50 °C, +100 °C, +160 °C at 20 mbar pressure. Price per thermoshelf | D00115 | |
| Subframe, tubular steel, black enamelled (for stacking unit consisting of vacuum oven and pump module, total height: 1650 mm, see "further data" and sketch of oven dimensions) | E02030 E02031 E02037 | |
| Signal cable (3 m) for control of roation speed and optimising pump performance by demand-controlled activation of purge of Memmert pump (not required with pump module) | B39410 | |
| Vacuum pump with chemically resistant 4x diaphragm, pump capacity at atm. pressures: approx. 50 Nl./min = 3,0 m/h3 and autom. purge control. Order No. B39410 and B04026 necessary. 230 V, 50 Hz. Max. guarantee period 2 years | E07509 | |
| Ethernet connection cable 5 m for computer interface | E06189 | |
| USB User-ID stick (with User-ID licence): Oven-linked authorisation licence (User-ID-programme) on Memory-stick, prevents undesired manipulation by unauthorised third parties. When reordering please specify serial number | B33170 | |
| Software conforming to FDA AtmoCONTROL. Meets the requirements for the use of electronically stored data sets and electronic signatures as laid down in Regulation 21 CFR Part 11 of the US Food and Drug Administration (FDA). Base licence for the control of one unit. Respective IQ/OQ documents available in German and English language (without surcharge) | FDAQ1 | |
| Integration of additional units (up to max. 15 units) into an alre ady existent FDA-software licence | FDAQ2 | |
| IQ document with device-specific works test data, OQ/PQ check list as support for validation by customer | D00124 | |
| IVF module for ICO50med: patented, consisting of 6 slide-in units, a total of 12 special racks with indentations for 12 Petri dishes (60 mm diam.) resp. 24 Petri dishes (35 mm diam.), 2 racks with indentations for 3 special media tubes each; racks with indentations for 4-well dishes on demand; only for ICO50med with the options K7 and F7; works calibration certificate (measuring point chamber centre) at +37 °C, 5 %, 6 % and 7 % CO2 as well as 90 % rh; 5 % O2 for IVF unit equipped with option T6 | B44128 | |
| IVF module for ICO105med: patented, consisting of 8 slide-in units, a total of 16 special racks with indentations for 16 Petri dishes (60 mm diam.) resp. 32 Petri dishes (35 mm diam.), 2 racks with indentations for 3 special media tubes each; racks with indentations for 4-well dishes on demand; only for ICO105med with the options K7 and F7; works calibration certificate (measuring point chamber centre) at +37 °C, 5 %, 6 % and 7 % CO2 as well as 90 % rh; 5 % O2 for IVF unit equipped with option T6 | B42398 | |
| IQ/OQ document with device-specific works test data for one freeselectable temperature value, incl. temperature distribution survey at Memmert for 9 measuring points to DIN 12876.2. Further temperature values and validation at customer site on demand. | D00125 | |
| Stacking set (consisting of stacking corners, one connecting plate for the rear, two wall brackets) for stacking two units ICO150med or ICO240med | B42114 B42115 | |
| Stainless steel bottom drip tray, 15 mm rim (can be used only in connection with option K1) | B34055 | |
| Stainless steel slide-in drip tray, 15 mm rim, with guide bars and fixing screws (can be used only in connection with option K1) | B32763 | |
| IQ/OQ document with device-specific works test data for one free-selectable CO2, humidity and temp. value, incl. temp. distribution survey at Memmert for 27 measuring points to DIN 12880:2007-05, PQ check list as support for validation by customer (models ICH C and ICOmed, on models ICOmed a free-selectable humidity value is only possible with option K7). Validation at customer site on demand. | D38897 | |
| HEPA-filter for chamber (filter class E11) according to EN 1822, packed in sterile condition, incl. fixing unit | B38739 | |
| Subframe (130 mm high); sizes 150/240: only in combination with the corresponding stacking sets for stacked appliances. | B33507 B33508 B33509 | |
| Subframe (622 mm high) adjustable in height (sizes 150/240: should not be used for 2 stacked units) | B33504 B33505 B33506 | |
| Additional water dish | B38737 B38000 | |
| IQ/OQ document with device-specific works test data for one freeselectable CO2 and temperature value, incl. temperature distribution survey at Memmert for 27 measuring points to DIN 12880:2007-05, PQ check list as support for validation by customer (models ICOmed). Price for validation at customer site on demand | D38898 | |
| IQ/OQ document with device-specific works test data for one free-selectable CO2, humidity and temperature value, incl. temperature distribution survey at Memmert for 27 measuring points to DIN 12880:2007-05, PQ check list as support for validation by customer (models ICH C and ICOmed, on models ICOmed a free-selectable humidity value is only possible with option K7). Price for validation at customer site on demand | D38897 | |
| Ethernet connection cable 5 m for computer interface | E06189 | |
|
Stainless steel grids, electropolished (standard equipment) | E28884 E20164 E20165 E28891 E20182 B32550 B41251 B38955 |
| Reinforced stainless steel grid, max. loading 60 kg, from size 450 with guide bars and fixing screws and only in connection with option K1 | E29767 E29766 B32190 | |
|
Perforated stainless steel shelf | B29727 B03916 B00325 B29725 B00328 B32549 B00326 |
|
Reinforced perforated stainless steel shelves, max. loading 60 kg, with guide bars and fixing screws and only in connection with option K1 | B32191 E29766 |
| Max. loading per slide-in drip tray (kg) | 1,5 3 4 8 5 | |
| Max. loading per bottom drip tray (kg) | 1,5 3 4 8 5 | |
|
Wall bracket for wall mounting | B29755 B29756 B29757 B29758 B29759 |
| Guarantee extension by 1 year | GA2Q5 | |
| Additional thermoshelves – aluminium eloxadised material W.-St. 3.3547 (ASTM B209) with integrated large-area heating including local temperature sensing (Pt100, 4-wire-circuit), individual overtemp. protection for each shelf MLOP (Multi-Level-Overtemperature-Control) and calibration certificate | B00741 B00743 B00744 | |
|
Additional thermoshelves – stainless steel material 1.4404 (ASTM 316 L) for especially corrosive material with integrated large-area heating including local temperature sensing (Pt100, 4-wire-circuit), individual overtemp. protection for each shelf MLOP (Multi-Level-Overtemperature-Control) and calibration certificate | B00733 B00734 B00735 |
| Removable bottom drip tray – stainless steel material 1.4404 (ASTM 316 L) | E04256 E04257 E04258 | |
|
Subframe, tubular steel, black enamelled (for stacking unit consisting of vacuum oven and pump module, total height: 1650 mm) Width/ Height/ Depth: model 200: 529/450/383, model 400: 529/290/463, model 500: 689/130/533 | E02030 E02031 E02037 |
| Works calibration certificate for 3 temperatures: +50°C, +100°C, +160°C at 20 mbar pressure | D00115 | |
| Guarantee extension by 1 year (VO only) | GA2Q5 | |
|
Noise-insulated vacuum pump module without pump (exterior dimensions and material No. see vacuum oven) with antivibration metal plate at the bottom to accommodate the vacuum pump, incl. full-sight glass door. Socket, signal cable and connecting hose to the vacuum oven | PM 200 PM 400 PM 500 |
|
Noise-insulated vacuum pump module, as above, however with built-in pump, 230 V, 50/60 Hz (pump B04133 for VO 200 and pump B04134 for VO 400 and 500) | PMP 200 PMP 400 PMP 500 |
| Signal cable (3 m) for optimising pump performance by demand-controlled activation of purge of Memmert pump | B04027 | |
|
Vacuum connecting hose (3 m) from oven to Memmert pump incl. optimised connection accessories (partially stainless steel) | B04026 |
|
Chemically resistant vacuum pump with PTFE double diaphragm, pump capacity at atm. pressures: approx. 34 Nl./min = 2,04 m³/h and autom. purge control from vacuum oven. Order No. B04027 and B04026 necessary. 230 V, 50/60 Hz. Max. guarantee period 2 years | B04133 |
|
Chemically resistant vacuum pump with PTFE double diaphragm, pump capacity at atm. pressures: approx. 60 Nl./min = 3,6 m³/h and autom. purge control from vacuum oven. Order No. B04027 and B04026 necessary. 230 V, 50/60 Hz. Max. guarantee period 2 years | B04134 |
|
Subframe, tubular steel, black enamelled (for stacking unit consisting of vacuum oven and pump module, total height: 1650 mm) Width/ Height/ Depth: model 200: 529/450/383, model 400: 529/290/463 | E02030 E02031 |
| Works calibration certificate for 3 temperatures: +5°C, +30°C, +90°C at 20 mbar pressure | D00133 | |
| Guarantee extension by 1 year (VOcool only) | GA2Q5 | |
| Reinforced stainless steel grid, max. loading 60 kg (size 750 with guide bars and fixing screws and only in connection with option K1) | E29767 E29766 B32190 | |
| Reinforced stainless steel grid, max. loading 60 kg, from size 450 with guide bars and fixing screws and only in connection with option K1 | E29767 E29766 B32190 | |
| Reinforced stainless steel grid, electropolished, max. loading 60 kg (model 750 with guide bars and fixing screws and only in connection with option K1) | E29767 E29766 B32190 | |
| Perforated stainless steel shelves | B00325 B29725 B00328 B32549 | |
|
Reinforced perforated stainless steel shelf, max. loading 60 kg, with guide bars and fixing screws and only in connection with option K1) | B32191 |
| Max. loading per slide-in drip tray (kg) | 3 4 8 | |
| Max. loading per bottom drip tray (kg) | 3 4 8 | |
| Holder for water tank (sizes 110 - 750: 2.5 litres, sizes 1060/1400: 10 litres) for mounting on the rear of the appliance. Standard equipment for sizes 750, 1060 and 1400. | E32172 | |
| Central water supply with filter cartridges for connection to the domestic water supply. Product information on demand. | ZWVR6 ZVWR6 | |
| Central water supply without filter cartridges for connection to the domestic water supply (only for demineralised water in accordance with VDE 0510/DIN EN 50272). Product information on demand | ZWVR7 | |
| Additional perforated stainless steel shelf | B00325 B00321 B03813 E35160 E37418 E35158 | |
|
Additional stainless steel grid | E20165 E20166 E29766 E20591 E20164 |
|
Subframe, adjustable in height (622 mm high) | B02792 B02732 B02793 |
| Subframe, (130 mm high for 2 stacked cabinets) | B02794 B02740 B02795 | |
| STERICard (additional or as replacement) for automatic chamber sterilisation cycle (not for sterilising the load!) | E04337 | |
|
Stainless steel gable cover, also suitable for shaking device (14/22 und 29/45) or Peltier cooling unit CDP 115 | B02641 B02642 B02643 B04390 |
|
Flat stainless steel cover with concentric ring sets for ring set openings: 1 opening / 147 mm diameter | B02680 |
|
Flat stainless steel cover with concentric ring sets for Peltier cooling CDP115: 1 opening / 147 mm diameter | B24372 |
|
Shelf reversible for 2 heights (30 or 60 mm) | E02893 E02894 E02895 E02896 |
|
Peltier cooling device CDP115 for waterbaths for temperatures below ambient from +10 °C, Voltage 230 V, 50/60 Hz, or 115 V, 60 Hz (please state in case of order). Please do not forget to order the installation and connection set! | CDP115 |
| Installation and connection set for Peltier cooling device CDP115 (incl. mounting bars for all different bath sizes) | B02770 | |
|
Shaking device incl. support frame, shaking frequency 35 – 160 strokes per minute (horizontal back/forth movement), requires gable cover | SV1422 SV2945 |
|
Support basket with perforated mounting shelf (stainless steel) with grid perforations to take clips for conical flasks | B02782 B04397 |
|
Flat stainless steel cover with concentric ring sets for ring set openings: 3 openings / 107 mm diameter | B02681 |
|
Flat stainless steel cover with concentric ring sets for Peltier cooling CDP115: 3 openings / 107 mm diameter | B24373 |
|
Portable stainless steel rack for 10 baby bottles: maximum capacity each bath: size 10: 1 rack, size 14: 2 racks, size 29: 4 racks | E02066 |
|
Flat stainless steel cover with concentric ring sets for ring set openings: 6 openings / 87 mm diameter | B02682 |
|
Flat stainless steel cover with concentric ring sets for Peltier cooling CDP115: 6 openings / 87 mm diameter | B04552 |
|
Clip for 100 ml flask, 12 flasks max. | B02692 |
|
Clip for 200 ml flask, 6 flasks max. | B02693 |
|
Clip for 300 ml flask, 6 flasks max. | B02694 |
|
Clip for 500 ml flask, 5 flasks max. | B02695 |
|
Rack for 110 test tubes 14.5 mm dia. | B02778 |
|
Rack for 90 test tubes 18 mm dia. | B02779 |
| Rack for 25 test tubes 32 mm dia. | B02780 | |
|
Flat stainless steel cover with concentric ring sets for ring set openings: 8 openings / 107 mm diameter | B02684 |
|
Flat stainless steel cover with concentric ring sets for ring set openings: 4 openings / 147 mm diameter | B02685 |
|
Flat stainless steel cover with concentric ring sets for Peltier cooling CDP115: 8 openings / 107 mm diameter | B04462 |
|
Clip for 100 ml flask, 18 flasks max. | B02692 |
|
Clip for 200 ml flask, 14 flasks max. | B02693 |
|
Clip for 300 ml flask, 14 flasks max. | B02694 |
|
Clip for 500 ml flask, 8 flasks max. | B02695 |
| Rack for 216 test tubes 14.5 mm dia. | B04399 | |
| Rack for 180 test tubes 18 mm dia. | B04400 | |
| Rack for 54 test tubes 32 mm dia. | B04401 | |
| Reinforced stainless steel grid, max. loading 60 kg (only in connection with option K1) | E20183 E20185 | |
| External control and logging package consisting of mini-Notebook and software „Celsius“, pre-configurated, and lateral swinging arm | B04410 | |
|
Stainless steel slide-in drip tray, 15 mm rim (may affect the temperature distribution) | E02070 E02072 E02073 |
|
Stainless steel bottom drip tray, 15 mm rim (may affect the temperature distribution) | B04356 B04358 B04359 |
|
Additional perforated stainless steel shelf, full width | B00325 B00321 B03813 |
|
Additional stainless steel grid, full width | E20165 E20166 E29766 |
|
Additional water dish (half width model 246) | B02787 B02784 B02786 |
|
Subframe (622 mm high) | B02792 B02732 B02793 |
| Subframe (130 mm hight for 2 stacked incubators) | B02794 B02740 B02795 | |
| HEPA-filter for chamber according to EN 1822, packed in sterile condition, incl. fixing unit | B04459 | |
| STERICard (additional or as replacement) for automatic chamber sterilisation cycle (not for sterilising load) | E04337 | |
| CO2 pressure reducing valve DIN 8546, incl. Gas cylinder monitor | E02087 | |
| N2 pressure reducing valve to DIN EN ISO 2503, incl. gas cylinder monitor (requires option T6) | E06162 | |
| Central water supply with filter cartridges for connection to the domestic water supply, only in combination with option K7. Product information on demand | ZWVR6 | |
| Central water supply without filter cartridges for connection to the domestic water supply (only for demineralised water in accordance with VDE 0510/DIN EN 50272), only in combination with option K7. Product information on demand | ZWVR7 | |
| Celltron benchtop shaker (not subject to discount) – accessories upon request | E06724 | |
| Additional perforated stainless steel shelve, half width | B02742 | |
| Stainless steel slide-in drip tray, 15 mm rim (may affect the temperature distribution) - cannot be used in connection with option K1 | E02070 E02072 E02073 E29726 E02075 B32599 E02068 B29726 | |
| Stainless steel bottom drip tray, 15 mm rim (may affect the temperature distribution) - cannot be used in connection with option K1 | B04356 B04358 B04359 B29722 B04362 B29769 B04360 | |
| Guarantee extension by 1 year | GA1Q5 GA2Q5 GA3Q5 GA4Q5 | |
| Module for external fresh water supply, only in combination with humidity module | B04712 | |
| Stainless steel grid | E20167 E20182 B04055 | |
| Flush-fit unit (stainless steel frame covering gap between oven and wall opening) – technical clarification necessary | B03190 B03188 | |
|
Loading set consisting of 8 grids, as well as 16 spacers - incl. 3 baskets for cups/glasses, made of stainless steel material no. 1.4301 (ASTM 304) | B04105 |
| USB connection cable for computer interface | E03643 | |
| Parallel/USB converter cable with integrated power supply unit to connect HP printers with USB interface to MEMMERT units. Not applicable for UFP800DW | E05300 | |
| Documentation package consisting of parallel USB converter cable including PCL3-compatible HP colour inkjet printer with USB interface (HP OfficeJet 6000 or successor) for direct connection of printer to Memmert unit. Not applicable for UFP800DW | B04432 | |
| Temperature profile write/read unit for programming via PC, for writing to and reading from the chip card, up to 40 ramps | E05284 | |
| Additional chip card, blank, formatted (32 kB MEMoryCard XL for a maximum of 40 ramps) | E04004 | |
| Oven-linked authorisation card (User-ID-Card) prevents undesired manipulation by unauthorised third parties. When reordering please specify serial number | E04159 | |
| Software conforming to FDA ”Celsius FDA Edition“ for up to 16 units. Meets the requirements for the use of electronically stored data sets and electronic signatures as laid down in Regulation 21 CFR Part 11 of the US Food and Drug Administration (FDA). Not applicable for UFP800DW | E05019 | |
| Integration of additional units (up to max.16 units) into an already existent FDA-software licence. Not applicable for UFP800DW | FDAQ4 | |
| IQ check list with works test data for chamber as support for validation by customer | D00103 | |
| OQ check list with works test data for one free-selectable temperature value incl. temperature distribution survey for 27 measuring points to DIN 12880:2007-05 as support for validation by customer | D00104 | |
| OQ check list with works test data for one free-selectable temperature and vacuum value incl. temperature distribution survey for 5 measuring points to DIN 12880:2007-05 as support for validation by customer (VO, VOcool only) valid for one thermoshelf, dito for further thermoshelves VO: EUR 340,– each | D00117 | |
| OQ check list with works test data for one free-selectable humidity and temperature value incl. temperature distribution survey for 27 measuring points to DIN 12880:2007-05 as support for validation by customer (models HCP and CTC) | D00104 | |
| OQ check list with works test data for one free-selectable CO2, humidity and temperature value incl. temperature distribution survey for 27 measuring points to DIN 12880:2007-05 as support for validation by customer (models INCOmed) | D00104 | |
| External measuring instrument with sensors for daylight and UV-light, with additional measuring head for temperature and humidity. Product information on demand (models HCP and CTC) | B04714 | |
|
Test tube racks, 56 holes (7x8), dia.18 mm each, bath capacity: 1 rack | B02781 |
|
Test tube racks, 24 holes (3x8), dia.18 mm each, bath capacity: 2 racks | B02783 |
|
Test tube rack, holes 2-row racks, 40 holes, dia. 10 mm each, width 40 mm | E02028 |
|
Test tube rack, holes 2-row racks, 40 holes, dia. 12 mm each, width 40 mm | E02013 |
|
Test tube rack, holes 2-row racks, 24 holes, dia. 14.5 mm each, width 43 mm | E02014 |
|
Test tube rack, holes 2-row racks, 24 holes, dia. 18 mm each, width 50 mm | E02022 |
|
Test tube rack, holes 2-row racks, 20 holes, dia. 21 mm each, width 55 mm | E02032 |
|
Test tube rack, holes 2-row racks, 12 holes, dia. 32 mm each, width 80 mm | E02034 |
|
Test tube rack, holes 3-row racks, 60 holes, dia. 10 mm each, width 50 mm | E02046 |
|
Test tube rack, holes 3-row racks, 60 holes, dia. 12 mm each, width 55 mm | E02049 |
|
Test tube rack, holes 3-row racks, 36 holes, dia. 14.5 mm each, width 60 mm | E02039 |
|
Test tube rack, holes 3-row racks, 36 holes, dia. 18 mm each, width 70 mm | E02019 |
|
Test tube rack, holes 3-row racks, 30 holes, dia. 21 mm each, width 80 mm | E02043 |
|
Test tube rack, holes 4-row racks, 80 holes, dia. 10 mm each, width 64 mm | E02057 |
|
Test tube rack, holes 4-row racks, 80 holes, dia. 12 mm each, width 75 mm | E02060 |
|
Test tube rack, holes 4-row racks, 48 holes, dia. 14.5 mm each, width 85 mm | E02056 |
|
Test tube rack, holes 4-row racks, 48 holes, dia. 18 mm each, width 95 mm | E02051 |
|
Test tube rack, holes 4-row racks, 40 holes, dia. 21 mm each, width 110 mm | E02061 |
| USB-Ethernet adapter | E06192 | |
| Ethernet connection cable 5 m for computer interface | E06189 | |
| USB User-ID stick (with User-ID licence): Oven-linked authorisation licence (User-ID-programme) on Memory-stick, prevents undesired manipulation by unauthorised third parties. When reordering please specify serial number (only for units with TwinDISPLAY) | B33170 | |
| USB stick with documentation software AtmoCONTROL and operation manual for products with SingleDISPLAY (the standard equipment of appliances with TwinDISPLAY includes one USB stick with AtmoCONTROL) | B33172 | |
| Set of height adjustable feet (4 pcs). Standard on models ICOmed | B29768 | |
|
Stacking set (4 pcs) for stacking of appliances of same size (not for models 160, 260, 450, 750, 1060, ICH110, ICH110L and ICH110C) | B29744 |
|
Plug-in tube extension (outer diam. 60,3 mm, inner 57 mm), straight, for exhaust air ducting (if necessary for connection by hose), only models U, I, S | B29718 |
|
Plug-in tube extension (outer diam. 60,3 mm, inner 57 mm), angled, for exhaust air ducting (if necessary for connection by hose), only models U, I, S | B29719 |
|
Flush-fit unit (stainless steel frame covering gap between oven and wall opening), with air slots – technical clarification required | B29728 B42116 B29742 B29730 B29732 B29734 B29736 B29738 B29740 B42118 |
|
Flush-fit unit (stainless steel frame covering gap between oven and wall opening), without air slots – technical clarification required | B29729 B42117 B29743 B33204 B33205 B33206 B33207 B29731 B29733 B29735 B29737 B29739 B29741 B42119 |
|
Subframe, adjustable in height (size 30 to 75: height 600 mm, size 110 to 450: height 500 mm) | b29745 B29745 B29747 B29749 B29751 B29753 |
|
Subframe, on castors (size 30 to 75: height 660 mm, size 110 to 160: height 560 mm) | B29746 B29748 B29750 |
| Subframe, adjustable in height (height 130 mm, for example for units with fresh-air filter) | B33657 B33659 B33661 B33664 | |
| Software conforming to FDA “AtmoCONTROL“. Meets the requirements for the use of electronically stored data sets and electronic signatures as laid down in Regulation 21 CFR Part 11 of the US Food and Drug Administration (FDA). Base licence for the control of one unit (only for units with TwinDISPLAY). Respective IQ/OQ documents available in German and English language (without surcharge). | FDAQ1 | |
| Integration of additional units (up to max. 15 units) into an already existent FDA-software licence (only for units with TwinDISPLAY) | FDAQ2 | |
| IQ document with device-specific works test data, OQ/PQ check list as support for validation by customer | D00124 | |
| IQ/OQ document with works test data for chamber, incl. temperature distribution survey for one free-selectable temperature value. 9 measuring points (size 30), 27 measuring points (sizes 55 - 1060) to DIN 12880:2007-05 (further temperature values on demand), PQ check list as support for validation by customer | D00125 D00127 | |
| IQ/OQ document with device-specific works test data for one free-selectable temperature and humidity value, incl. temperature distribution survey at Memmert for 27 measuring points (26 measuring points on model HPP1400) to DIN 12880:2007-05, PQ check list as support for validation by customer (models HPP and ICH). Validation at customer site on demand. | D00136 | |
| IQ/OQ document with works test data for chamber, incl. temperature distribution survey for one free-selectable temperature, humidity and light value. 27 measuring points to DIN 12880:2007-05, PQ check list as support for validation by customer (models HPP with light and ICH L) | D00137 | |
| External measuring instrument with sensors for daylight and UV-light. Product information on demand (models HPP, ICH L, IPPplus) | B04713 | |
| External measuring instrument with sensors with additional measuring head for temperature and humidity measurement. Product information on demand (models HPP, ICH, ICH L, ICH C, IPPplus and ICOmed) | B04714 |
| Order No. | ||
|---|---|---|
| Additional reinforced perforated stainless steel shelf, max. loading 60 kg; with guide bars and fixing screws (only in connection with option K1). Please consider max. loading of chamber | B32191 |
