| Option | Order No. | |
|---|---|---|
| Works calibration certificate for one temperature according to customer specification (only TTC) | D00109 | |
| Door-hinges on left side | B8 | |
| Works calibration certificate for one temperature and humidity according to customer specification (only CTC) | D00105 | |
| Full-sight glass door (5-layer insulating glazing), heated | B0 | |
| Entry port, left, 80 mm, with stopper | F0 | |
| Start-up of CTC and TTC chambers and brief training (D, A, CH only) through Memmert service, (not subject to discount) | K9 | |
| Interface Ethernet instead of USB including software | W4 | |
| RS232 interface instead of USB | W6 | |
| Computer interface RS485 (for networking a max. of 16 ovens) instead of RS232 | V2 | |
| Door with lock (safety lock, not available for VO, VOcool, TTC/CTC) | B6 | |
|
Flexible Pt100 for positioning in chamber or in load with socket, 4-pin, according to NAMUR NE 28, for external temperature recording (load temperature) | H4 |
|
Flexible Pt100 temperature sensor, positioned flexibly in chamber or load, for local temperature measurement (up to 3 additional sensors are possible). The measured temperature can, if required, be indicated on the multifunction display, recorded in the integral ring store, and can be documented via the “Celsius” software or on an attached printer. (not available for VO, VOcool, TTC and CTC) | H8 |
|
Potential-free contact (24 V/2 A) with socket, according to NAMUR NE 28 for external monitoring (indicates when setpoint is reached); VO only in combination with option T5 | H5 |
|
Potential-free contact (24 V/2 A) with socket, according to NAMUR NE 28 for combination error message (e.g. supply failure, sensor fault, fuse); VO only in combination with option T5 | H6 |
|
Potential-free contact (24 V/2 A) with socket, according to NAMUR NE 28, triple, for signal generation, controlled by programme segment for a total of 3 freely selected functions to be activated (e.g. acoustic and visual signals, exhaust motors, fans, stirrers etc.) | H7 |
| Accessory | Order No. | |
|---|---|---|
|
Stainless steel grids, electropolished (standard equipment) | |
|
Additional stainless steel grid | E20591 |
| External control and logging package consisting of mini-Notebook and software „Celsius“, pre-configurated, and lateral swinging arm | B04410 | |
| USB connection cable for computer interface | E03643 | |
| Temperature profile write/read unit for programming via PC, for writing to and reading from the chip card, up to 40 ramps | E05284 | |
| Additional chip card, blank, formatted (32 kB MEMoryCard XL for a maximum of 40 ramps) | E04004 | |
| Oven-linked authorisation card (User-ID-Card) prevents undesired manipulation by unauthorised third parties. When reordering please specify serial number | E04159 | |
| Software conforming to FDA ”Celsius FDA Edition“ for up to 16 units. Meets the requirements for the use of electronically stored data sets and electronic signatures as laid down in Regulation 21 CFR Part 11 of the US Food and Drug Administration (FDA). Not applicable for UFP800DW | E05019 | |
| Integration of additional units (up to max.16 units) into an already existent FDA-software licence. Not applicable for UFP800DW | FDAQ4 | |
| IQ check list with works test data for chamber as support for validation by customer | D00103 | |
| OQ check list with works test data for one free-selectable temperature value incl. temperature distribution survey for 27 measuring points to DIN 12880:2007-05 as support for validation by customer | D00144 | |
| OQ check list with works test data for one free-selectable temperature and vacuum value incl. temperature distribution survey for 5 measuring points to DIN 12880:2007-05 as support for validation by customer (VO, VOcool only) valid for one thermoshelf, dito for further thermoshelves VO: EUR 340,– each | D00117 | |
| External measuring instrument with sensors for daylight and UV-light, with additional measuring head for temperature and humidity. Product information on demand (models HCP and CTC) | B04714 |
